linkedintwitter
Annuaire  |  Flux RSS  |  Espace presse  |  Wiki IJL  |  Webmail  |  Videos  |    Photos   Articles scientifiques  Articles scientifiques 

Publications: Articles

Annees:  
Toutes :: 2007, ... , 2010, 2011, 2012, ... , 2014
Auteurs:  
Tous :: A, B, C, D, E, F, G, H, I, J, K, L, M, N, P, R, S, T, V, W, X, Y, Z 
Tous :: Aeby-Gautier, ... , Anders, Anglada, Appolaire, ... , Azim 
Preferences: 
References par page: Mots clefs Voir les resumes
References

Articles:

Appolaire, Benoit, Perevoshchikova, Nataliya, Teixeira, Julien and Denis, Sabine
Solid State Phenomena, 172-174(Part 1):1214-1219
2011
ISSN: 1012-0394

Resume: We have adapted the Quickhull algorithm with the general dimension Beneath-Beyond algorithm [6] for computing the convex hull of the Gibbs energy hypersurface of multicomponent two-phase alloys. We illustrate the salient features of our method with calculations of isothermal ferrite-austenite equilibria in Fe-C-Cr. Finally, successive equilibrium calculations in a Fe-C-Cr-Mo steel over a large temperature range show the benefit of computing the convex hull before performing the conventional Newton-Raphson search.

Equipe: Département SI2M : Microstructures et Contraintes

Dehmas, M., Kovac, J., Aeby-Gautier, E., Appolaire, B., Denand, B. and Da-Costa-Teixeira, J.
Solid State Phenomena, 172-174:396-401
2011

Equipe: Département SI2M : Microstructures et Contraintes

Hell, Jean-Christophe, Dehmas, Moukrane, Allain, Sebastien, Prado, Juscelino Mendes, Hazotte, Alain and Chateau, Jean-Philippe
ISIJ International, 51(10):1724-1732
2011
ISSN: 0915-1559

Resume: We elaborated two carbide-free bainitic steels with different microstructures through specific alloy design and austempering process. Microstructural characterizations were performed by means of EBSD analysis and in-situ high energy synchrotron diffraction in order to evaluate the phase fractions and the carbon content in the retained austenite, as well as the microtextures. These microstructural features were correlated to the tensile properties. Both steels exhibited an excellent compromise between high strength (above 1 250 MPa), good ductility (uniform elongation up to 14%) and high fracture strain (reduction of area up to 46%). The volume fraction of MA blocks (blocks of retained austenite partially transformed into fresh martensite during the final cooling at room temperature) was a key relevant parameter that strongly influenced the work-hardening at the expense of the damaging processes at high strain.

Equipe: Département SI2M : Microstructures et Contraintes

Di Napoli, P., Appolaire, B., Aeby-Gautier, E. and Bénéteau, A.
Solid State Phenomena, 172-174:1044-1049
2011

Equipe: Département SI2M : Microstructures et Contraintes

Settefrati, A., Aeby-Gautier, E., Dehmas, M., Geandier, G., Appolaire, B., Audion, S. and Delfosse, J.
Solid State Phenomena, 172-174(Part 1):760-765
2011
ISSN: 1012-0394

Resume: In the present study we focus on the precipitation processes during heating and ageing of beta-metastable phase in the near beta Ti-5553 alloy. Transformation processes have been studied using continuous high energy X-Ray Diffraction (XRD) and electrical resistivity for two different states of the beta-metastable phase. Microstructures have been observed by electron microscopy. Different transformation sequences are highlighted depending on both heating rate and chemical composition of the beta-metastable phase. At low temperatures and low heating rates, the hexagonal omega(iso) phase is first formed as generally mentioned in the literature. Increasing the temperature, XRD evidences the formation of an orthorhombic phase (alpha"), which evolves toward the hexagonal pseudo compact alpha phase. For higher heating rates or for richer composition in beta-stabilizing elements of the beta-metastable phase, omega phase may not form and alpha" forms directly and again transforms into alpha phase. A direct transformation from beta-metastable to alpha phase is observed for the highest heating rate. The formation of the metastable omega(iso) and alpha" phases clearly influences the final morphology of alpha.

Equipe: Département SI2M : Microstructures et Contraintes

Cette annee / Total:
5 / 31
Exporter au format:
BibTeX, XML